{"id":5364,"date":"2026-11-11T18:28:52","date_gmt":"2026-11-12T02:28:52","guid":{"rendered":"https:\/\/www.26yc.com\/single-phase-immersion-exchanger-interface\/"},"modified":"2026-11-11T18:28:52","modified_gmt":"2026-11-12T02:28:52","slug":"single-phase-immersion-exchanger-interface","status":"publish","type":"post","link":"https:\/\/www.26yc.com\/ja\/single-phase-immersion-exchanger-interface\/","title":{"rendered":"Single-Phase Immersion Won the Retrofit. Here Is Where the Exchanger Goes."},"content":{"rendered":"<h1>Single-Phase Immersion Won the Retrofit. Here Is Where the Exchanger Goes.<\/h1>\n<p>Two-phase immersion had the better physics on paper. It also needed fluorinated dielectric fluids whose supply and regulatory position have been deteriorating for years, with PFAS restrictions and the wind-down of legacy Novec products pushing operators toward simpler loops. In 2026 the practical default for high-density retrofits is direct-to-chip cold plates, with single-phase immersion reserved for the sites that genuinely need maximum density. That shift changes the heat-recovery interface more than most equipment catalogues admit.<\/p>\n<h2>The grade of heat, by architecture<\/h2>\n<table>\n<thead>\n<tr>\n<th>Cooling architecture<\/th>\n<th>Typical rejection temperature<\/th>\n<th>What the recovery loop looks like<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Room air \/ CRAC<\/td>\n<td>25\u201335\u00b0C<\/td>\n<td>Air-to-air core on the exhaust, then a large heat-pump lift. Rarely economic for external supply.<\/td>\n<\/tr>\n<tr>\n<td>Rear-door exchanger<\/td>\n<td>35\u201345\u00b0C water<\/td>\n<td>Marginal grade; usually needs a heat pump.<\/td>\n<\/tr>\n<tr>\n<td>Direct-to-chip cold plate<\/td>\n<td>45\u201355\u00b0C<\/td>\n<td>Plate exchanger into a secondary water loop, then network or process load.<\/td>\n<\/tr>\n<tr>\n<td>Single-phase immersion<\/td>\n<td>50\u201360\u00b0C fluid<\/td>\n<td>Best available grade; still belongs behind a plate exchanger, not in an air duct.<\/td>\n<\/tr>\n<tr>\n<td>Two-phase immersion<\/td>\n<td>50\u201365\u00b0C condensing<\/td>\n<td>Same, plus fluid-handling and vapour-management complexity.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>The pattern is simple: the higher the source temperature, the less electricity the heat pump needs. A 50\u201360\u00b0C source works with a COP in the 3.5\u20135.0 range for a modest lift into a low-temperature network; a 30\u00b0C air stream does not. This is why we stopped describing air-cooled halls as a heat-recovery opportunity in our own proposals. The heat exists. The economics usually do not.<\/p>\n<h2>The interface detail that gets drawn wrong<\/h2>\n<p>An immersion tank is a sealed dielectric-fluid system with its own materials compatibility, pump skid and service procedure. Putting an air-to-air core anywhere near it solves nothing. What you want is a <strong>plate heat exchanger between the dielectric loop and a secondary water loop<\/strong>: it isolates an expensive fluid from a district or process circuit, gives you a clean metering point for the heat purchase agreement, and keeps the server-side warranty boundary intact. On the air side, the only legitimate job is the building&#8217;s own ventilation \u2014 support rooms, UPS rooms, and any residual air-cooled fraction.<\/p>\n<figure><img decoding=\"async\" src=\"https:\/\/www.26yc.com\/wp-content\/uploads\/2026\/11\/single-phase-immersion-exchanger-interface.svg\" alt=\"Immersion tank dielectric loop connected through a plate heat exchanger to a secondary water loop and heat network\" style=\"max-width:100%;height:auto;border:1px solid #e6ebef;border-radius:8px;\" \/><figcaption>Keep the dielectric fluid on one side of the plate pack. The metering point belongs on the other side.<\/figcaption><\/figure>\n<p>We would also insist on a bypass and isolation valves on that plate exchanger. The IT cooling loop has to keep running when the heat customer stops taking heat \u2014 a summer weekend, a network outage, a commissioning delay. A recovery interface that cannot be isolated is a single point of failure for the entire hall. It sounds obvious; we have seen P&#038;IDs where the heat-recovery branch had no bypass.<\/p>\n<h2>Selection consequences for the core supplier<\/h2>\n<p>Two things follow. First, most of the high-grade duty in these projects is liquid-to-liquid, so a plate exchanger specified for water\/glycol service is the relevant product, not a ventilation core. Second, the air-side scope that remains should be specified against the usual air-to-air criteria: airflow, face velocity, pressure drop, leakage and frost margin. Our <a href=\"\/ja\/plate-vs-rotary-vs-heat-pipe\/\">plate vs rotary vs heat-pipe comparison<\/a> \u304a\u3088\u3073 <a href=\"\/ja\/plate-heat-exchanger\/\">plate exchanger working principle<\/a> cover that side; the <a href=\"\/ja\/liquid-cooling-waste-heat-reuse\/\">liquid-cooling waste-heat guide<\/a> covers the liquid side.<\/p>\n<p>One opinion we will stand behind: the choice between cold plate and immersion should follow the rack density and the service model, not the heat-reuse ambition. A project that picks immersion mainly because it produces nicer waste-heat temperatures has the decision order backwards. We go through the same logic in <a href=\"\/ja\/bess-thermal-management\/\">BESS thermal management<\/a>, where the temperature-uniformity requirement, not the recovery opportunity, sets the architecture.<\/p>\n<p>For the temperature matching at the network end, see the <a href=\"\/ja\/data-center-waste-heat-recovery-guide\/\">data centre recovery guide<\/a>.<\/p>","protected":false},"excerpt":{"rendered":"<p>Keep the dielectric fluid on one side of the plate pack.<\/p>","protected":false},"author":0,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[242],"tags":[],"class_list":["post-5364","post","type-post","status-publish","format-standard","hentry","category-exchanger-types"],"_links":{"self":[{"href":"https:\/\/www.26yc.com\/ja\/wp-json\/wp\/v2\/posts\/5364","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.26yc.com\/ja\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.26yc.com\/ja\/wp-json\/wp\/v2\/types\/post"}],"replies":[{"embeddable":true,"href":"https:\/\/www.26yc.com\/ja\/wp-json\/wp\/v2\/comments?post=5364"}],"version-history":[{"count":0,"href":"https:\/\/www.26yc.com\/ja\/wp-json\/wp\/v2\/posts\/5364\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.26yc.com\/ja\/wp-json\/wp\/v2\/media?parent=5364"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.26yc.com\/ja\/wp-json\/wp\/v2\/categories?post=5364"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.26yc.com\/ja\/wp-json\/wp\/v2\/tags?post=5364"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}