Marine Drying & Waste Heat Recovery Units

Tこの装置は、魚、エビ、貝、海藻を含む水産副産物の効率的な乾燥と加工のために設計されています。熱回収システムを統合し、エネルギー効率を最大化しながら運用コストを削減します。塩に耐えるステンレス鋼で完全に構成され、過酷な海洋および高塩分環境での長期耐久性を確保します。持続可能な水産加工、廃棄物最小化、省エネ運用に最適です。

主な特長：

 

• 魚、エビ、貝、海藻の残さの乾燥・加工に適している

• 省エネ運転のための内蔵熱回収システム

• 塩分腐食に耐える高品質ステンレス鋼構造

• 廃棄物量を削減し、環境持続可能性を向上させる

• 過酷な海洋条件向けの耐久性がありメンテナンスの少ない設計

Marine and coastal processing sites face two pressures at once: high energy cost for thermal drying and a corrosive environment that destroys ordinary equipment. This heat-recovery drying unit answers both. A built-in air-to-air plate recuperator captures heat from the humid exhaust leaving the drying chamber and uses it to preheat the incoming fresh air, so the burner or electric heater only supplies the remaining temperature lift. In continuous seafood processing this recirculation of energy can remove a large share of the heating load.

Construction is the other half of the story. Every wetted and exposed surface is built from salt-resistant stainless steel, typically 304 for mildly corrosive duty and 316L where seawater spray or high salt loads are expected. The smooth stainless surfaces are easy to wash down, helping sites meet HACCP and food-safety hygiene expectations for fish, shrimp, shellfish, and seaweed processing. Because the unit reduces the volume of processing residue and recovers energy at the same time, operators see lower utility bills and less solid waste to dispose of. For vessels and shore plants alike, the low-maintenance, corrosion-proof design means the equipment keeps running through long seasons with minimal downtime.

よくある質問

What makes this unit resistant to salt corrosion?
All wetted and exterior surfaces are built from salt-resistant stainless steel, with 316L specified where seawater spray or high salinity is expected. Stainless avoids the rapid pitting and rust that would shorten the life of ordinary carbon-steel equipment in marine duty.

How does the integrated heat-recovery system save energy?
A built-in air-to-air plate recuperator transfers heat from the humid exhaust to the incoming fresh drying air. The heating system then supplies only the remaining temperature lift, cutting the fuel or electricity needed for drying.

Can the equipment handle different seafood by-products?
Yes. The unit is configured for fish, shrimp, shellfish, and seaweed residues, and the modular layout adapts to different throughput and moisture loads common in seafood processing.

Does it support food-safety requirements?
The stainless contact surfaces are easy to clean and wash down, which supports HACCP and general hygiene programs in food processing. Closed, recoverable airflow also helps control odors and emissions.

よくある質問

What makes this unit resistant to salt corrosion?

All wetted and exterior surfaces are built from salt-resistant stainless steel, with 316L specified where seawater spray or high salinity is expected. Stainless avoids the rapid pitting and rust that would shorten the life of ordinary carbon-steel equipment in marine duty.

How does the integrated heat-recovery system save energy?

A built-in air-to-air plate recuperator transfers heat from the humid exhaust to the incoming fresh drying air. The heating system then supplies only the remaining temperature lift, cutting the fuel or electricity needed for drying.

Can the equipment handle different seafood by-products?

Yes. The unit is configured for fish, shrimp, shellfish, and seaweed residues, and the modular layout adapts to different throughput and moisture loads common in seafood processing.

Does it support food-safety requirements?

The stainless contact surfaces are easy to clean and wash down, which supports HACCP and general hygiene programs in food processing. Closed, recoverable airflow also helps control odors and emissions.