The flow velocity selection for an air-to-air heat exchanger depends on the operating conditions, exchanger type, design objectives, and fluid properties. The following are recommendations and typical ranges:
- Typical flow velocity range
- Gas velocity: 10–30 m/s.
- Low velocity (~10 m/s): for pressure-drop-sensitive or energy-saving scenarios.
- High velocity (~20–30 m/s): for enhanced heat transfer; watch pressure drop and vibration.
- Plate heat exchanger: 5–15 m/s.
- Shell-and-tube exchanger: shell side 1–5 m/s, tube side 10–20 m/s.
- Gas velocity: 10–30 m/s.
- Factors in velocity selection
- Heat-transfer efficiency: Higher velocity enhances turbulence and raises the heat-transfer coefficient, but too high may reduce residence time.
- Pressure drop and energy consumption: High velocity increases pressure drop and power use; a balance is needed.
- Equipment life: Excessively high velocity may cause vibration, noise, or corrosion; too low may cause fouling.
- Flow-channel design: Channel width, length, and layout affect velocity distribution.
- Recommended velocity range
- General recommendation: 8–15 m/s.
- Special cases:
- Energy-saving priority: 5–10 m/s, ensuring turbulence.
- High heat-transfer efficiency: 15–20 m/s, evaluating pressure drop and vibration.
- Design reference: Calculate velocity from heat load (Q = m·Cp·ΔT) and flow rate (Q = V·A).
- How to determine the optimal velocity
- Calculate the Reynolds number: ensure Re > 2100 (Re = ρ·V·D/μ).
- Simulation and testing: Use CFD software or design tools (such as HTRI, Aspen).
- Field adjustment: Adjust valves based on temperature difference and flow rate; observe effects and pressure drop.
- Precautions
- Fluid properties: Density, specific heat, and viscosity affect velocity selection.
- Exchanger material: Sensitive materials require lower velocity.
- Operating conditions: High temperature or corrosive gas requires special control.
- Regular maintenance: Low velocity may cause fouling; cleaning is required.
- Summary It is recommended to control the velocity at 8–15 m/s; the specific value should be determined by calculation or simulation based on exchanger type, fluid properties, heat load, and operating conditions. Use professional software to optimize at the design stage and adjust based on actual operating data to balance heat-transfer efficiency, energy consumption, and equipment life.
よくある質問
What is a typical gas velocity for air-to-air exchangers?
Gas velocity is often discussed in a moderate range; plate types run lower than shell-and-tube, and the best value balances heat transfer against pressure drop.
Why not maximize velocity?
Higher velocity raises the heat-transfer coefficient but also fan power, noise, vibration, and fouling risk, so an optimum exists.
How does velocity affect pressure drop?
Pressure drop grows quickly with velocity, so oversizing velocity can erase energy gains from better heat transfer.
Should velocity differ by exchanger type?
Yes. Plate, rotary, and shell-and-tube designs each have characteristic ranges tied to their geometry and allowable loss.
よくある質問
What is a typical gas velocity for air-to-air exchangers?
Gas velocity is often discussed in a moderate range; plate types run lower than shell-and-tube, and the best value balances heat transfer against pressure drop.
Why not maximize velocity?
Higher velocity raises the heat-transfer coefficient but also fan power, noise, vibration, and fouling risk, so an optimum exists.
How does velocity affect pressure drop?
Pressure drop grows quickly with velocity, so oversizing velocity can erase energy gains from better heat transfer.
Should velocity differ by exchanger type?
Yes. Plate, rotary, and shell-and-tube designs each have characteristic ranges tied to their geometry and allowable loss.
適切な熱交換器を選定
当社のエンジニアが風量、温度、圧力損失の予算に合わせてコアを設計し、用途に応じて板式・回転式・ヒートパイプ回収を選定します。以下をお読みください: 熱交換器ガイド 、または仕様についてお問い合わせください。
関連製品
HVAC および換気向けの板式・回転式・ヒートパイプ回収。
空気と液体用の大表面積固定コア。
大風量向け高効率エネルギー回収。
清浄用途向けの受動的・完全分離流。