Marine Drying & Waste Heat Recovery Units

T이 장비는 생선, 새우, 조개, 해조류를 포함한 수산 부산물의 효율적인 건조 및 가공을 위해 설계되었습니다. 열 회수 시스템을 통합하여 에너지 효율을 극대화하는 동시에 운영 비용을 절감합니다. 염분에 강한 스테인리스강으로 전체가 구성되어 가혹한 해양 및 고염분 환경에서 장기 내구성을 보장합니다. 지속 가능한 수산 가공, 폐기물 최소화, 에너지 절약 운영에 이상적입니다.

주요 특징:

 

• 생선, 새우, 조개, 해조류 잔류물의 건조 및 가공에 적합

• 에너지 효율적 운전을 위한 내장형 열 회수 시스템

• 염분 부식에 강한 고품질 스테인리스강 구조

• 폐기물 양을 줄이고 환경 지속 가능성을 향상시킵니다

• 가혹한 해양 조건을 위한 내구성 있고 유지보수가 적은 설계

Marine and coastal processing sites face two pressures at once: high energy cost for thermal drying and a corrosive environment that destroys ordinary equipment. This heat-recovery drying unit answers both. A built-in air-to-air plate recuperator captures heat from the humid exhaust leaving the drying chamber and uses it to preheat the incoming fresh air, so the burner or electric heater only supplies the remaining temperature lift. In continuous seafood processing this recirculation of energy can remove a large share of the heating load.

Construction is the other half of the story. Every wetted and exposed surface is built from salt-resistant stainless steel, typically 304 for mildly corrosive duty and 316L where seawater spray or high salt loads are expected. The smooth stainless surfaces are easy to wash down, helping sites meet HACCP and food-safety hygiene expectations for fish, shrimp, shellfish, and seaweed processing. Because the unit reduces the volume of processing residue and recovers energy at the same time, operators see lower utility bills and less solid waste to dispose of. For vessels and shore plants alike, the low-maintenance, corrosion-proof design means the equipment keeps running through long seasons with minimal downtime.

자주 묻는 질문

What makes this unit resistant to salt corrosion?
All wetted and exterior surfaces are built from salt-resistant stainless steel, with 316L specified where seawater spray or high salinity is expected. Stainless avoids the rapid pitting and rust that would shorten the life of ordinary carbon-steel equipment in marine duty.

How does the integrated heat-recovery system save energy?
A built-in air-to-air plate recuperator transfers heat from the humid exhaust to the incoming fresh drying air. The heating system then supplies only the remaining temperature lift, cutting the fuel or electricity needed for drying.

Can the equipment handle different seafood by-products?
Yes. The unit is configured for fish, shrimp, shellfish, and seaweed residues, and the modular layout adapts to different throughput and moisture loads common in seafood processing.

Does it support food-safety requirements?
The stainless contact surfaces are easy to clean and wash down, which supports HACCP and general hygiene programs in food processing. Closed, recoverable airflow also helps control odors and emissions.

자주 묻는 질문

What makes this unit resistant to salt corrosion?

All wetted and exterior surfaces are built from salt-resistant stainless steel, with 316L specified where seawater spray or high salinity is expected. Stainless avoids the rapid pitting and rust that would shorten the life of ordinary carbon-steel equipment in marine duty.

How does the integrated heat-recovery system save energy?

A built-in air-to-air plate recuperator transfers heat from the humid exhaust to the incoming fresh drying air. The heating system then supplies only the remaining temperature lift, cutting the fuel or electricity needed for drying.

Can the equipment handle different seafood by-products?

Yes. The unit is configured for fish, shrimp, shellfish, and seaweed residues, and the modular layout adapts to different throughput and moisture loads common in seafood processing.

Does it support food-safety requirements?

The stainless contact surfaces are easy to clean and wash down, which supports HACCP and general hygiene programs in food processing. Closed, recoverable airflow also helps control odors and emissions.