Single-Phase Immersion Won the Retrofit. Here Is Where the Exchanger Goes.
Two-phase immersion had the better physics on paper. It also needed fluorinated dielectric fluids whose supply and regulatory position have been deteriorating for years, with PFAS restrictions and the wind-down of legacy Novec products pushing operators toward simpler loops. In 2026 the practical default for high-density retrofits is direct-to-chip cold plates, with single-phase immersion reserved for the sites that genuinely need maximum density. That shift changes the heat-recovery interface more than most equipment catalogues admit.
The grade of heat, by architecture
| Cooling architecture | Typical rejection temperature | What the recovery loop looks like |
|---|---|---|
| Room air / CRAC | 25–35°C | Air-to-air core on the exhaust, then a large heat-pump lift. Rarely economic for external supply. |
| Rear-door exchanger | 35–45°C water | Marginal grade; usually needs a heat pump. |
| Direct-to-chip cold plate | 45–55°C | Plate exchanger into a secondary water loop, then network or process load. |
| Single-phase immersion | 50–60°C fluid | Best available grade; still belongs behind a plate exchanger, not in an air duct. |
| Two-phase immersion | 50–65°C condensing | Same, plus fluid-handling and vapour-management complexity. |
The pattern is simple: the higher the source temperature, the less electricity the heat pump needs. A 50–60°C source works with a COP in the 3.5–5.0 range for a modest lift into a low-temperature network; a 30°C air stream does not. This is why we stopped describing air-cooled halls as a heat-recovery opportunity in our own proposals. The heat exists. The economics usually do not.
The interface detail that gets drawn wrong
An immersion tank is a sealed dielectric-fluid system with its own materials compatibility, pump skid and service procedure. Putting an air-to-air core anywhere near it solves nothing. What you want is a plate heat exchanger between the dielectric loop and a secondary water loop: it isolates an expensive fluid from a district or process circuit, gives you a clean metering point for the heat purchase agreement, and keeps the server-side warranty boundary intact. On the air side, the only legitimate job is the building’s own ventilation — support rooms, UPS rooms, and any residual air-cooled fraction.
We would also insist on a bypass and isolation valves on that plate exchanger. The IT cooling loop has to keep running when the heat customer stops taking heat — a summer weekend, a network outage, a commissioning delay. A recovery interface that cannot be isolated is a single point of failure for the entire hall. It sounds obvious; we have seen P&IDs where the heat-recovery branch had no bypass.
Selection consequences for the core supplier
Two things follow. First, most of the high-grade duty in these projects is liquid-to-liquid, so a plate exchanger specified for water/glycol service is the relevant product, not a ventilation core. Second, the air-side scope that remains should be specified against the usual air-to-air criteria: airflow, face velocity, pressure drop, leakage and frost margin. Our plate vs rotary vs heat-pipe comparison 및 plate exchanger working principle cover that side; the liquid-cooling waste-heat guide covers the liquid side.
One opinion we will stand behind: the choice between cold plate and immersion should follow the rack density and the service model, not the heat-reuse ambition. A project that picks immersion mainly because it produces nicer waste-heat temperatures has the decision order backwards. We go through the same logic in BESS thermal management, where the temperature-uniformity requirement, not the recovery opportunity, sets the architecture.
For the temperature matching at the network end, see the data centre recovery guide.
적합한 열교환기 선정
당사 엔지니어가 풍량, 온도, 압력 손실 예산에 맞춰 코어를 설계하고, 적용에 따라 판형·회전식·히트파이프 회수를 선택합니다. 다음을 읽으세요: 열교환기 가이드 , 또는 사양 관련 문의를 주세요.
관련 제품
HVAC 및 환기용 판형·회전식·히트파이프 회수.
공기 및 액체용 대면적 고정 코어.
대풍량용 고효율 에너지 회수.
청정 적용을 위한 수동적·완전 분리 유동.